White wooden box

Create a cool storage box with sliding lid from plywood and finish it off with Resene Colorwood Enhance and Resene Aquaclear.

Download PDF

Ways with wood with Mark Rayner - Project 42

Difficulty level: Moderate

You will need: 20mm plywood cut to the following dimensions:
330mm x 500mm for the base
330mm x 280mm for the sides
500mm x 250mm for the front and back
9mm plywood cut to 330mm x 496mm for the lid
Two 30mm x 10mm timber mouldings cut to 340mm
20mm x 10mm timber moulding cut to 536mm, 475mm and 170mm
Two 10mm x 10mm timber mouldings cut to 290mm, 40mm panel pins, 16mm craft pins, hammer, paintbrush, paint stirrer, pencil, PVA glue, sandpaper, saw, set square and tape measure. Resene Aquaclear satin and Resene Colorwood Enhance white.

To get the look: Mark painted the background wall with Resene SpaceCote Flat tinted to Resene Nero and the table top with Resene Enamacryl tinted to Resene Half Alabaster.

Other ideas: For a shiny dark effect use Resene Colorwood Enhance black mixed with Resene Aquaclear gloss.

Step one
Measure, mark and cut the plywood and timber moulding to the above dimensions and lengths. Smooth any rough edges with sandpaper.

Step two
Attach the front and back sections to the base, as shown, fixing in place with panel pins and PVA glue.

Step three
Attach the side sections into position, as shown, fixing with panel pins and PVA glue.

Step four
Attach the 10mm x 10mm pieces of moulding to the inside of each side piece, as shown, ensuring each end is flush with the front and back sections. Fix with craft pins and PVA glue.

Step five
Attach the longest piece of 20mm x 10mm moulding along the back edge, as shown, ensuring the ends are flush with the sides. Fix with panel pins, craft pins and PVA glue.

Step six
Attach the next longest piece of 20mm x 10mm moulding at right angles to the back edge and the two lengths of 30mm x 10mm moulding along the side edges, as shown, and fix with panel pins, craft pins and PVA glue. Attach the last piece of 20mm x 10mm moulding to the lid to form a handle.

Step seven
Mix the Resene Colorwood Enhance into the Resene Aquaclear and stir thoroughly with a paint stirrer.

Step eight
Apply two coats of the coloured Resene Aquaclear to the box and lid, allowing two hours for each coat to dry. Slide the lid into position.

Other projects you might like to try

Bathroom revamp
Weekend DIY

Painted fireplace
Weekend DIY

Modern mailbox
Ways with wood

Garden edging
Ways with wood

Potting bench
Weekend Gardener

Rustic birdhouse
Weekend Gardener

View more projects

Resene Paints Ltd – www.resene.com

We would love to hear from you if you wish to use Resene's images, information and ideas for social medial, blogs, newsletters and other media use. Please email update@resene.co.nz and let us know what you need, what it is for and how Resene will be acknowledged as the source of the content. We are happy to assist with most requests.

Our vision is to be respected as a trusted, ethical and sustainable company and acknowledged as the leading provider of innovative paint and colour technology. View Resene’s profile, Quality Policy, Environmental Policy and Health & Safety Policy.

Any personal data, such as name, address, phone, email details, supplied to Resene for the purposes of receiving newsletters, orders etc will be retained by Resene Paints Ltd and used only by Resene Paints Ltd and its trusted agencies for the purposes of communication/promotion/providing service to you. We do not sell, trade or otherwise transfer your personal data to outside third parties. If you wish to opt out of communication from Resene please complete our contact us form. View our full Privacy Policy.

Colours shown on this website are a representation only. Please refer to the actual paint or product sample. Resene colour charts, testpots and samples are available for ordering online. See measurements/conversions for more details on how electronic colour values are achieved.