Close Give Feedback
Resene Paints - home page
Facebook Pinterest Instagram YouTube

Painting new unpainted concrete


Resene Popular Paint Systems –
Concrete, plasters and cement-based substrates: training notes

This web page is an edited version of the Resene Best System Selling training notes provided to Resene staff and is provided to enable you to gain a greater understanding of the substrates and paint systems you may encounter in your decorating project. It is impossible to cover all decorating scenarios in a single document, so if you are in doubt about any aspect of your project please contact Resene for assistance.

How to paint new unpainted concrete


(Preparation)

Note: Refer to the PDF flowchart for a visual of the steps below:

  1. Wash down with Resene Paint Prep and Housewash to remove dirt, oils and other contaminants.

  2. Fill cracks and voids:

    1. Cracks under 1mm, use Resene Brushable Crack Filler.
    2. Cracks over 1mm, use Selleys No More Gaps exterior formulation or similar.
    3. Holes and voids, use either Resene Jointflex or an approved masonry filler.
  3. Prime using Resene Concrete Primer.

  4. Refer to topcoat systems flowcharts.

NOTE: Resene Limelock may be used on new concrete and plaster to enhance the cure and hold back limestaining. It is most effective when applied during the construction stage.

New unpainted concrete

Things to consider

Notes:

  1. Concrete (and thickly applied plasters) may take up to 28 days to fully cure and, unless Resene Limelock is used, should not be painted before this time.

  2. Curing and release agents will need to be removed from concrete before painting. In most cases Resene Paint Prep and Housewash will do the job, but for stubborn release agents a stronger product like Resene Emulsifiable Solvent Cleaner should be used. This is rarely an issue for DIY paint users (see appendix).

  3. Plasters, masonry finishes and cement sheets will collect dust and air-blown contaminants, such as salt, on the surface. A thorough wash and hose down should be sufficient to remove plaster dust etc. from the surface.

  4. Concrete will sometimes have minor cracks and bug holes. These are best filled with plaster, such as Rockcote Multistop, or alternatively an epoxy, such as Resene Epox-O-Bond. Use a spatula or 35-50mm broad knife.

  5. Plasters and masonry may have small hairline cracks caused as the plaster dries. It is often difficult due to the rough nature of the surface to use a filler, so use Resene Brushable Crack Filler or Resene X-200 brushed into the cracks.

  6. Apply Resene Concrete Primer before filling any cracks or voids.

    • Applying fillers is easier if the surface is sealed.
    • The primer will make it easier to identify cracks to be filled.
  7. Resene Limelock is recommended for new plasters and masonry. Resene Concrete Primer will help prevent subsequent limestaining. When dark colours are used, allow at least 7 days before overcoating Resene Limelock.

Key accessories essential to complete the job

Add-ons – to make the job easier or quicker

Return to index

 

Order online now:
Testpots | Paints | Primers and Sealers | Stains | Clears | Accessories

Get inspired Get inspired ! Subscribe      Get saving Get saving ! Apply for a DIY card

Resene Paints Ltd

Can't find what you're looking for? Ask us!

Resene Paints Ltd   – www.resene.com

Follow us on Facebook Follow us on Pinterest Follow us on Instagram Follow us on YouTube
Videos on how to paint and stain your house
 

Welcome to our World of Colour!™
Colours shown on this website are a representation only. Please refer to the actual paint or product sample. Resene colour charts, testpots and samples are available for ordering online.   See measurements/conversions for more details on how electronic colour values are achieved.

What's new | Specifiers | Painters | DIYers | Artists | Kids | Sitemap | Home | TOP ⇧