Close Give Feedback
Resene Paints - home page
Facebook Pinterest Instagram YouTube

Crown Interior Low Sheen

interior – waterborne

Technical Data Sheet C04 5-25

This data sheet replaces all previous issues

Crown Interior Low Sheen is based on a 100% acrylic low odour resin and has been formulated specifically for easy application. This results in an attractive and washable low sheen finish ideal for most interior surfaces.

Crown Interior Low Sheen - 4L paint container

Typical uses

Performance

  1. Excellent adhesion to primed and natural substrates, timber, concrete and old paintwork.

  2. Excellent intercoat adhesion.

  3. A low sheen, washable wall paint.

Limitations

  1. Do not apply at temperatures below 10°C or when it is liable to drop below 10°C during the drying period.

  2. Do not use in wet areas, such as bathrooms, kitchens or laundries.

  3. Do not use on opening sashes and doors where two painted areas come into contact.

  4. Will not penetrate chalky or powdery surfaces.

  5. Do not apply direct to metal.

  6. Galvanised steel must be suitably primed before application.

Physical properties

Vehicle type 100% acrylic
Pigmentation Titanium dioxide/fillers
Solvent Water
Finish Low Sheen
Colour Crown White and selected Resene Total Colour System, including BS5252, Multi- Finish, Whites & Neutrals and The Range colours tinted off white View Resene colour charts online or the online Resene colour library
Abrasion resistance Good
Chemical resistance Good
Heat resistance Fair - Thermoplastic
Solvent resistance Poor - Sensitive to alcohols and aromatic hydrocarbons
Durability Excellent

Surface preparation

All surfaces

Clean the surface thoroughly to remove all dirt, dust and loose material. Ensure the surface is free from oil, grease and mould. If moss and mould are present, treat with Resene Moss & Mould Killer (see Data Sheet D80)

Refer to Resene Surface Information Preparation Data Sheets (SIPDS), available online at www.resene.com/datasheets, for full substrate specific surface preparation information.

All sanding dusts can be harmful. Always wear appropriate protection.

Seek expert advice if working with lead, chromate or asbestos based materials or surfaces.


Priming

Primer required Yes, dependent on surface. Ensure the correct substrate primer and/or sealer is used. Fill nail holes and surface imperfections after priming.

Interior plasterboard – new dry areas

Crown Wallboard Sealer see Data Sheet C06) or Resene Broadwall Waterborne Wallboard Sealer (see Data Sheet D403).

Interior plasterboard – existing dry areas

Resene Waterborne Sureseal (see Data Sheet D42a) or Resene Sureseal (see Data Sheet D42).

Fibrous plasterboard and hardboard

Solventborne Resene Sureseal (see Data Sheet D42).

Timber

Crown Acrylic Primer Undercoat (see Data Sheet C06), Resene Quick Dry (see Data Sheet D45) or Resene Enamel Undercoat (see Data Sheet D44).

Refer to Resene Technical Services or the Resene website, www.resene.com/datasheets, for full substrate specific priming and Resene coating system/specification information.


Application

Apply by Brush, speed brush, synthetic fibre roller or spray
16 square metres per litre per coat
Dry film thickness 25 microns at 16 square metres per litre
Dry time (minimum) 45 minutes at 20°C
Recoat time (minimum) 2 hours at 20°C
Usual no. of coats 2
Thinning Water
Clean up Water

Stir thoroughly before use. Fill all nail holes and cracked timber after priming. Apply two full coats of Crown Interior Low Sheen allowing dry time between coats.


Precautions

Please read the current Technical Data Sheet and Safety Data Sheet before specifying or using Resene products. Resene Technical Data Sheets are updated from time to time. This Technical Data Sheet is provided as a guide for this product and may differ from the most recent version. Please discuss your project with your Resene Technical Representative, local Resene ColorShop team or reseller to ensure you have the right products to give you the best quality finish for your specific project.


Product stewardship

Return any unwanted product or packaging to the Resene PaintWise recycling service (NZ) or Paintback (AU).


Downloads

Please read the Safety Data Sheet (SDS) before use.

View:

Buy in-store


Need more advice?

Ask a Resene Paint Expert free online  |  Ask a Resene Colour Expert free online

Ask a Resene Paint Expert free online

Ask a Resene Colour Expert free online

Please read the current Technical Data Sheet and Safety Data Sheet before specifying or applying Resene products. View Technical Data Sheets and Safety Data Sheets with VOCs online at www.resene.com/datasheets. If in doubt contact Resene.

 

Order online now:
Testpots | Paints | Primers and Sealers | Stains | Clears | Accessories

Get inspired Get inspired ! Subscribe      Get saving Get saving ! Apply for a DIY card

Resene Paints Ltd

Can't find what you're looking for? Ask us!

Resene Paints Ltd   – www.resene.com

Follow us on Facebook Follow us on Pinterest Follow us on Instagram Follow us on YouTube
Videos on how to paint and stain your house
 

Welcome to our World of Colour!™
Colours shown on this website are a representation only. Please refer to the actual paint or product sample. Resene colour charts, testpots and samples are available for ordering online.   See measurements/conversions for more details on how electronic colour values are achieved.

What's new | Specifiers | Painters | DIYers | Artists | Kids | Sitemap | Home | TOP ⇧