Crown Acrylic Enamel Semi Gloss

Typical uses

• Architraves
• Bathrooms
• Furniture
• Kitchens
• Laundries
• Plywood
• Skirtings
• Timber doors
• Wallboards
• Window frames/joinery

Performance

1. May be used wherever solventborne enamels have been traditionally used.

2. Non-yellowing.

3. May be applied over Crown Acrylic Primer Undercoat (see Data Sheet C06).

4. Clean, spatter free application.

Limitations

1. Do not apply at temperatures below 10°C or when it is liable to drop below 10°C during the drying period.

2. Ensure the correct primers and/or sealers are used.

3. Due to waxes in fibre and particle board, it is essential that a first coat of Crown Acrylic Primer Undercoat (see Data Sheet C06) is applied before applying topcoats.

Physical properties

Vehicle type	New generation acrylic
Pigmentation	Titanium dioxide
Solvent	Water
Finish	Semi-gloss
Colour	Crown White and selected Resene Total Colour System, including BS5252, Multi- Finish, Whites & Neutrals and The Range colours tinted off white View Resene colour charts online or the online Resene colour library
Abrasion resistance	Very good
Chemical resistance	Fair
Heat resistance	Good
Solvent resistance	Good
Durability	Excellent

Surface preparation

All surfaces

Clean the surface thoroughly to remove all dirt, dust and loose material. Ensure the surface is free from oil, grease and mould. If moss and mould are present, treat with Resene Moss & Mould Killer (see Data Sheet D80)

Refer to Resene Surface Information Preparation Data Sheets (SIPDS), available online at www.resene.com/datasheets, for full substrate specific surface preparation information.

All sanding dusts can be harmful. Always wear appropriate protection.

Seek expert advice if working with lead, chromate or asbestos based materials or surfaces.

---

Priming

Primer required

Yes. Ensure the correct substrate primer and/or sealer is used.

Timber

Crown Acrylic Primer Undercoat (see Data Sheet C06), Resene Quick Dry (see Data Sheet D45) or Resene Wood Primer (see Data Sheet D40).

Fibre and particle board

Crown Acrylic Primer Undercoat (see Data Sheet C06) or Resene Quick Dry (see Data Sheet D45).

Cementitious surfaces

Resene Concrete Primer (see Data Sheet D405) or solventborne Resene Sureseal (see Data Sheet D42).

Interior plasterboard – wet areas

Resene Waterborne Sureseal (see Data Sheet D42a) or Resene Sureseal (see Data Sheet D42).

Refer to Resene Technical Services or the Resene website, www.resene.com/datasheets, for full substrate specific priming and Resene coating system/specification information.

---

Application

Apply by	Brush, speed brush, synthetic fibre roller or spray
Typical coverage (spreading rate)	18 square metres per litre per coat
Dry film thickness	23 microns at 18 square metres per litre
Dry time (minimum)	45 minutes at 20°C
Recoat time (minimum)	2 hours at 20°C
Usual no. of coats	2
Thinning	Water
Clean up	Water

Stir thoroughly before use. Apply two full coats of Crown Acrylic Enamel Semi-Gloss allowing dry time between coats.

Do not use with Resene Wintergrade Additive.

---

Precautions

Please read the current Technical Data Sheet and Safety Data Sheet before specifying or using Resene products. Resene Technical Data Sheets are updated from time to time. This Technical Data Sheet is provided as a guide for this product and may differ from the most recent version. Please discuss your project with your Resene Technical Representative, local Resene ColorShop team or reseller to ensure you have the right products to give you the best quality finish for your specific project.

---

Product stewardship

Return any unwanted product or packaging to the Resene PaintWise recycling service (NZ) or Paintback (AU).

---

Downloads

Please read the Safety Data Sheet (SDS) before use.

• Safety Data Sheet

View:

• Technical Data Sheet
• Label

Buy in-store