Architects memo no. 9: May 1981
Colorwood stain - its development and uses

Staining is an art whose origins stretch back into antiquity; the woad of the ancient Britains (also used by the Chinese) is one of the earliest stains recorded. Dyes were obtained from variety of natural sources: cochineal from insects, Tyrian purle from Mediterranean molluscs, plus a wide variety of fruits, berries, dyewoods, peats, lichens etc. The dyes were dissolved in water, balsams, oils, and ferments to produce the earliest stains.

By definition, stains are materials designed primarily to impart colour effects to surfaces rather than to form a protective coating.

Modern stains flourished with the start of the synthetic dye industry about the turn of the century. Today there are literally hundreds of dyes to choose from, each belonging to one of four basic dye-based types:

  1. Waterborne
    The water-soluble dyes are probably the most lightfast but are very difficult to apply uniformly and they raise the grain of timber badly.
  2. Oil soluble
    Easy to apply but tend to have very poor lightfastness.
  3. Spirit soluble
    These have fair lightfastness but are very rapid drying. Great skill is needed to apply them to large areas.
  4. N.G.R. stains
    This class of stain attempts to combine all the good properties of the preceding three. They achieve fair lightfastness, have slight grain-raising and reasonable ease of application. Considerable skill is still needed, however, to achieve uniformity over large areas.

It has, of course, long been recognised that pigments (as against dyes) have excellent lightfastness. But, because they are opaque, pigments have not been used much in transparent stains.

Some time ago, one of the problems of the paint industry has been the difficulty in making lead-free bright reds, oranges and yellows with good obliteration properties. The reason for this is that readily available organic pigments tend to be transparent in oil-based media. This can be explained technically by referring to the refractive index of pigments.

"When a solid is immersed in a liquid of the same refractive index, the solid seems to disappear (i.e. like putting glass into water). This is the case when solids (organic reds and yellows) are mixed with liquid paint media".

The technical staff at Resene concluded that these phenomena could be harnessed to produce a new and exciting kind of wood stain.

The result - Resene Colorwood: a range of colours possessing excellent lightfastness while maintaining complete transparency. Other benefits are controlled penetration and a medium-slow evaporation rate that makes application virtually foolproof on all but highly porous surfaces.

Resene Colorwood colours are concentrated. Paler shades are achieved by dilution with specially formulated Resene Colorwood Reducing Base. Other colours can also be created by intermixing any of the Resene Colorwood range. Grain highlights result from the natural differences in porosity between spring and summer bands of wood. The more porous areas absorb more stain to create deeper tones. For maximum highlighting effect, excess Resene Colorwood should be wiped off the hard grain with an absorbent lint-free cloth.

Application by brush is the normal method of applying Resene Colorwood. But porous materials, such as chipboard or cork, can draw Resene Colorwood from the brush and create dark spots. Here, use of a pad is recommended to achieve perfect uniformity.

Properly applied, Resene Colorwood will dry in eight hours. Excessive application in an attempt to increase colour density only prolongs drying. Correct colour strength is best achieved by using the right shade rather than heavy coats of a lighter one.

Resene Colorwood has been successfully applied to all common timbers, particle boards, cork, cane, hessian and ropework.

For protection Resene Colorwood can be overcoated, but not with average varnishes and urethanes. These tend to 'yellow'to the detriment of the vivid Resene Colorwood colour beneath. Resene has produced a special range of polyurethane finishes with minimum yellowing characteristic. It consists of Resene Poly-Gloss, Resene Poly-Satin and Resene Poly-Flat - the latter possessing excellent grain filling properties and, as such, is recommended as a first coat whatever final finish is required.

In 1995 Resene launched Resene Aquaclear, a waterborne alternative to turps - thinned oil-modified varnish. Resene Aquaclear can be washed up in water and gives off low odour on application. In only a few years, Resene Colorwood has almost completely replaced dye-based stains in the architectural market. Its success has been due to its ready acceptance by architects, specifying authorities and painters alike. While for the home handyman Resene Colorwood has opened-up all sorts of exciting possibilities.

Refer to Data Sheets D50A, D52 and D59 for further information.

Download as a pdf. (You will need Acrobat Reader).

Resene Paints Ltd

Resene Paints Ltd   –

We would love to hear from you if you wish to use Resene's images, information and ideas for social medial, blogs, newsletters and other media use. Please email and let us know what you need, what it is for and how Resene will be acknowledged as the source of the content. We are happy to assist with most requests.

Our vision is to be respected as a trusted, ethical and sustainable company and acknowledged as the leading provider of innovative paint and colour technology. View Resene’s profile, Quality Policy, Environmental Policy and Health & Safety Policy.

Any personal data, such as name, address, phone, email details, supplied to Resene for the purposes of receiving newsletters, orders etc will be retained by Resene Paints Ltd and used only by Resene Paints Ltd and its trusted agencies for the purposes of communication/promotion/providing service to you. We do not sell, trade or otherwise transfer your personal data to outside third parties.. If you wish to opt out of communication from Resene please complete our contact us form. View our full Privacy Policy.

Colours shown on this website are a representation only. Please refer to the actual paint or product sample. Resene colour charts, testpots and samples are available for ordering online.   See measurements/conversions for more details on how electronic colour values are achieved.

View Videos